Prev
Next
A TEAM WORKING AT THE NEWMONT AKYEM SITE
ASSEMLING OF SAG MILL FEED CHUTE AT NEWMONT AHAFO
CHECKING ELEVATION LEVELS WITH AN OPTICAL MICROMETER
CHECKING FOR BASE PLATE LEVELNESS
CHECKING MILL SHELL BOLTS.
CHECKING THE CENTRE LINE OF A BASE PLATE WITH A PLUMB BULB
CHECKING THE CENTRE LINE OF A BASE PLATE WITH A PLUMB BUILD
CHECKING THE LEVELNESS OF A BASE PLATE WITH A MACHINIST LEVEL
CLEANING OF ANCHOR BOLT THREAD BEFORE INSTALLATION
COMPLETED THE INSTALLATION OF A NEW GEARBOX COUPLING AT NEWMONT AHAFO SITE
FIRST TEAM TO START THE NEWMONT AHAFO SAG MILL INSTALLATION ON LINE 2
FIXING A FITTED STUD INTO A SHELL TO SHELL FLANGE JOINT
FIXING A HYDRAULIC MOTOR ON AN INCHING DRIVE
FIXING BOLTS INTO A SECTION OF THE MILL DISCHARGE HEAD.
FIXING OF A LOW SPEED COUPLING ON A GEARBOX
FIXING OF JACKING SCREW FOR BASE PLATE INSTALLATION
FIXING THE BOTTOM SECTION OF BOLTS INTO TRUNNION BEFORE INSTALLATION
FIXING TRUNNION INTO TRUNNION PEDESTAL
HEATING A COUPLING TO BE INSTALLED AT AGA OBUASI STP PLANT
IMG_20181010_152512
INITIAL CHECKS OF A MILL CENTRE LINES.
INSPECTING A COUPLING TO BE FIXED
INSTALLATION OF A GEARBOX BASE PLATE
INSTALLING A 6.5 MW MILL MOTOR
INSTALLING A JACKING SCREW UNDER THE BASE OF A MOTOR BASE PLATE
INSTALLING A MILL GEARBOX
INSTALLING A MILL PINION
A RIGGED TRUNNION WITH THE TRUNNION BEARING READY FOR INSTALLATION
INSTALLING A SECTION OF A 38' X 18' SAG MILL AT NEWMONT AHAFO SITE
INSTALLING HYDRAULIC JACKS UNDER MILL JACKING CRADLE
INSTALLING LOAD CELL ON TRUNNION BASE PLATE
INSTALLING THE DISCHARGE END TRUNNION WITH THE TRUNNION BEARING AT NEWMONT AHAFO LINE 2
INSTALLING THE ECCENTRIC OF A CONE CRUSHER IN A QUARRY AT BUDUMBURA
INSTALLING THE FIRST SECTION OF THE MILL GIRTH GEAR AT AHAFO LINE 2
INSTALLING THE HIGH SPEED COUPLING OF A 6.5 MW MOTOR OF A MILL
INSTALLING THE LAST SECTION OF THE MILL SHELL AT NEWMONT AHAFO LINE 2
INSTALLING THE UPPER SECTION OF A SAG MILL FEED END BASE PLATE
MIXING EPOXY GROUT TO BE POURED AT NEWMONT AHAFO LINE 2
P_20180424_234730
POLISHING SHELL TO SHELL FLANGE HOLE TO FIX A FITTED STUD
POLISHING THE FITTED STUD HOLE OF THE BOTTOM SECTION OF THE MILL SHELL SECTION
POLISHING THE TOP OF A MILL MOTOR BASE PLATE
PREPARING TO INSTALL A LOW SPEED COUPLING ON A GEARBOX
REMOVAL OF A PINION BASE PLATE FOR RE-ALIGNMENT AT GOLDEN STAR BOGOSO - Copy
RIGGING THE LAST SECTION OF A SAG MILL SHELL FOR INSTALLATION
ROUGH ALIGNING THE MILL MOTOR
SETTING AN OPTICAL MICROMETER FOR ELEVATION CHECKS
SHOOTING ELEVATION LEVELS WITH THE OPTICAL MICROMETER
INSTALLING A NEW SPHERICAL ROLLER BEARING ON A MILL TRUNNION AT GOLDEN STAR BOGOSO
Prev
Next
Leaking mill flange joint.
Injection of stratathane into the horizontal leaking flange of the Ahafo Ball Mill.
Bogoso trunnion bearing.
Bogoso trunnion bearing change out.
Bogoso trunnion bearing change out.
GOLDEN STAR RESOURCES - (BOGOSO)Changing of a spherical roller bearing of the Ball Mill trunnion at Bogoso mine site.
Picture showing the damaged trunnion bearing of the Bogoso Ball Mill.
Ahafo sag mill pinion
Inspection of a new pinion shaft to be installed on the Newmont Ahafo Sag Mill RHS drive.
Technical Director at SYAMA in Mali,
Technical Director at Iduapriem
Technical Director at Morocco
A refurbished swing jaw stock being installed at Golden Star Resources Wassa Mine at the time of working with Metso Ghana Limited.
GOLDEN STAR RESOURCES - (BOGOSO)Changing of a refurbished gearbox on their Ball Mill.
AHAFO SITE (Changing of Sag Mill RHS pinion shaft)
Ahafo sag mill pinion
An opened mill shell flange, sand blasted for repairs
A removed trunnion bearing sleeve.
Removal of trunnion bearing sleeve for inspection.
Ball mill of the BMC plant in Burkina Youga town.
Working with personnel from Burkina Mining Company
Front view of the BMC Ball Mill
Inspection of a trunnion bearing sleeve.
A repaired leaking mill Flange
Prev
Next
